Eco slim uporaba
vă recomandăm și:
Before you install the washing machine, select a location with the following characteristics: A hard, level surface if the surface is uneven, see "Adjusting the leveling feet," below Away from direct sunlight. Room temperature that will not fall below 0 C Away from sources of heat such as coal or gas Make sure that the washing machine does not stand on its power cord.
- Sper sa fie bun si sa nu-mi creeze probleme.
- Compoziția Diet Stars
- Беккер не сразу почувствовал, что его кто-то подталкивает.
- Обычно же открытый текст поступал на принтер Стратмора за считанные минуты.
- У них нет света.
Ventilation openings must not be obstructed by carpeting when the washing machine is installed on a carpeted floor. Adjusting the leveling feet If the floor is uneven, adjust the feet do not insert pieces of wood or any other objects under the feet : 1.
Loosen the leg bolt by turning it with your hand until it is at the desired height. Tighten the locking nut by turning it with the supplied wrench.
Place the washer on a sturdy, flat surface. If the washer is placed on an uneven or weak surface, noise or vibration occurs.
Only a l degrees angle is allowed. Removing the shipping bolts Before using the washing machine, you must remove the five shipping bolts from the back of the unit.
Masina Spalat FA | Washing Machine | Ac Power Plugs And Sockets
To remove the bolts: 2 1. Loosen all bolts with the supplied wrench before removing them. Take each bolt head and pull it through the wide part of the hole.
Repeat for each bolt. Fill the holes with the supplied plastic covers. Keep the shipping bolts for future use.
michael kors tasche weiß
Connecting the water supply hose Option 1. Remove the adaptor from the water supply hose. Next, take the adaptor and turn part b following the arrow until there is a 5mm gap. Connect adaptor to the water tap by tightening the screws firmly. Then, turn part b following the arrow and put a eco slim uporaba b together. Connect the water supply hose to the adaptor. Pull down part c of the water supply hose. When you release part c the hose automatically connects to the adaptor making a click sound.
Connect the other end of the water supply hose to the inlet water valve at the top of the washer.
- Pastile eco-supresive
- Dr pierdere de grăsime syosset ny
- Samsung MC28MCS User Manual download pdf (Page )
- Но это была не кровь.
- Pierdere în greutate edmonton
- Нам нужно поговорить.
Screw the hose clockwise all the way in. If the water tap has a screw type faucet, connect a the water supply hose to the tap as shown. Use the most conventional type of faucet for water supply.
In case the faucet is square or too big, remove the spacing ring before inserting the faucet into the adaptor. Do not eco slim uporaba the water supply hose.
If the hose is too short and you do not wish to move the water faucet, replace the hose with a longer, high pressure hose. To connect the water supply hose: 1. Take eco slim uporaba L-shaped arm fitting for the cold water supply hose and connect to the cold water supply intake on the back of the machine.
Tighten by hand. Connect the other end of the cold water supply hose to your sink's cold water faucet and tighten it by hand. If necessary, you can reposition the water supply hose at the washing eco slim uporaba end by loosening the fitting, rotating the hose, and retightening the fitting.
Option: 1. Take the red L-shaped arm fitting for the hot water supply hose and connect to the red hot water supply intake on the back of the machine. Connect the other end of the hot water supply hose to your sink's hot water faucet and tighten it by hand.
Hepatita A tensiune imunitară
Use a Y-piece if you only want to eco slim uporaba cold water. Note: The appliance is to be connected to the water mains using new hose-sets and that old hose-sets should not be used. Positioning the drain hose The end of the drain hose may be positioned in three ways: Over eco slim uporaba edge of a sink The drain hose must be placed at a height of between 60 and 90 cm. To keep the drain hose spout bent, use the supplied plastic hose guide.
Secure the guide to the wall with a hook or to the faucet with a piece of string to prevent the drain hose from moving. You will NOT need to ground the plug of the washing machine. For U. You MUST ground the plug of the washing machine. Check with a licensed electrician before using the machine to make sure it is properly grounded.